Use correct angle tune range of +/-30 on PMW33XX (#17693)
Co-authored-by: Daniel Kao <daniel.m.kao@gmail.com> Co-authored-by: Daniel Kao <daniel.m.kao@gmail.com>
This commit is contained in:
parent
f5e16f94d5
commit
580bcff4f6
3 changed files with 99 additions and 93 deletions
|
@ -22,11 +22,11 @@ POINTING_DEVICE_DRIVER = adns5050
|
|||
|
||||
The ADNS 5050 sensor uses a serial type protocol for communication, and requires an additional light source.
|
||||
|
||||
| Setting | Description |
|
||||
|--------------------|---------------------------------------------------------------------|
|
||||
|`ADNS5050_SCLK_PIN` | (Required) The pin connected to the clock pin of the sensor. |
|
||||
|`ADNS5050_SDIO_PIN` | (Required) The pin connected to the data pin of the sensor. |
|
||||
|`ADNS5050_CS_PIN` | (Required) The pin connected to the cable select pin of the sensor. |
|
||||
| Setting | Description |
|
||||
| ------------------- | ------------------------------------------------------------------- |
|
||||
| `ADNS5050_SCLK_PIN` | (Required) The pin connected to the clock pin of the sensor. |
|
||||
| `ADNS5050_SDIO_PIN` | (Required) The pin connected to the data pin of the sensor. |
|
||||
| `ADNS5050_CS_PIN` | (Required) The pin connected to the cable select pin of the sensor. |
|
||||
|
||||
The CPI range is 125-1375, in increments of 125. Defaults to 500 CPI.
|
||||
|
||||
|
@ -40,13 +40,13 @@ POINTING_DEVICE_DRIVER = adns9800
|
|||
|
||||
The ADNS 9800 is an SPI driven optical sensor, that uses laser output for surface tracking.
|
||||
|
||||
| Setting | Description | Default |
|
||||
|--------------------------------|------------------------------------------------------------------------|---------------|
|
||||
|`ADNS9800_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
|
||||
|`ADNS9800_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
|
||||
|`ADNS9800_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `3` |
|
||||
|`ADNS9800_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
|`ADNS9800_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
| Setting | Description | Default |
|
||||
| ----------------------- | ---------------------------------------------------------------------- | ------------- |
|
||||
| `ADNS9800_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
|
||||
| `ADNS9800_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
|
||||
| `ADNS9800_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `3` |
|
||||
| `ADNS9800_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
| `ADNS9800_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
|
||||
|
||||
The CPI range is 800-8200, in increments of 200. Defaults to 1800 CPI.
|
||||
|
@ -61,16 +61,16 @@ POINTING_DEVICE_DRIVER = analog_joystick
|
|||
|
||||
The Analog Joystick is an analog (ADC) driven sensor. There are a variety of joysticks that you can use for this.
|
||||
|
||||
| Setting | Description | Default |
|
||||
|----------------------------------|----------------------------------------------------------------------------|---------------|
|
||||
|`ANALOG_JOYSTICK_X_AXIS_PIN` | (Required) The pin used for the vertical/X axis. | _not defined_ |
|
||||
|`ANALOG_JOYSTICK_Y_AXIS_PIN` | (Required) The pin used for the horizontal/Y axis. | _not defined_ |
|
||||
|`ANALOG_JOYSTICK_AXIS_MIN` | (Optional) Sets the lower range to be considered movement. | `0` |
|
||||
|`ANALOG_JOYSTICK_AXIS_MAX` | (Optional) Sets the upper range to be considered movement. | `1023` |
|
||||
|`ANALOG_JOYSTICK_SPEED_REGULATOR` | (Optional) The divisor used to slow down movement. (lower makes it faster) | `20` |
|
||||
|`ANALOG_JOYSTICK_READ_INTERVAL` | (Optional) The interval in milliseconds between reads. | `10` |
|
||||
|`ANALOG_JOYSTICK_SPEED_MAX` | (Optional) The maximum value used for motion. | `2` |
|
||||
|`ANALOG_JOYSTICK_CLICK_PIN` | (Optional) The pin wired up to the press switch of the analog stick. | _not defined_ |
|
||||
| Setting | Description | Default |
|
||||
| --------------------------------- | -------------------------------------------------------------------------- | ------------- |
|
||||
| `ANALOG_JOYSTICK_X_AXIS_PIN` | (Required) The pin used for the vertical/X axis. | _not defined_ |
|
||||
| `ANALOG_JOYSTICK_Y_AXIS_PIN` | (Required) The pin used for the horizontal/Y axis. | _not defined_ |
|
||||
| `ANALOG_JOYSTICK_AXIS_MIN` | (Optional) Sets the lower range to be considered movement. | `0` |
|
||||
| `ANALOG_JOYSTICK_AXIS_MAX` | (Optional) Sets the upper range to be considered movement. | `1023` |
|
||||
| `ANALOG_JOYSTICK_SPEED_REGULATOR` | (Optional) The divisor used to slow down movement. (lower makes it faster) | `20` |
|
||||
| `ANALOG_JOYSTICK_READ_INTERVAL` | (Optional) The interval in milliseconds between reads. | `10` |
|
||||
| `ANALOG_JOYSTICK_SPEED_MAX` | (Optional) The maximum value used for motion. | `2` |
|
||||
| `ANALOG_JOYSTICK_CLICK_PIN` | (Optional) The pin wired up to the press switch of the analog stick. | _not defined_ |
|
||||
|
||||
### Cirque Trackpad
|
||||
|
||||
|
@ -89,15 +89,15 @@ POINTING_DEVICE_DRIVER = cirque_pinnacle_spi
|
|||
|
||||
This supports the Cirque Pinnacle 1CA027 Touch Controller, which is used in the TM040040, TM035035 and the TM023023 trackpads. These are I2C or SPI compatible, and both configurations are supported.
|
||||
|
||||
| Setting | Description | Default |
|
||||
|-------------------------------- |------------------------------------------------------------|--------------------|
|
||||
|`CIRQUE_PINNACLE_X_LOWER` | (Optional) The minimum reachable X value on the sensor. | `127` |
|
||||
|`CIRQUE_PINNACLE_X_UPPER` | (Optional) The maximum reachable X value on the sensor. | `1919` |
|
||||
|`CIRQUE_PINNACLE_Y_LOWER` | (Optional) The minimum reachable Y value on the sensor. | `63` |
|
||||
|`CIRQUE_PINNACLE_Y_UPPER` | (Optional) The maximum reachable Y value on the sensor. | `1471` |
|
||||
|`CIRQUE_PINNACLE_DIAMETER_MM` | (Optional) Diameter of the trackpad sensor in millimeters. | `40` |
|
||||
|`CIRQUE_PINNACLE_ATTENUATION` | (Optional) Sets the attenuation of the sensor data. | `ADC_ATTENUATE_4X` |
|
||||
|`CIRQUE_PINNACLE_CURVED_OVERLAY` | (Optional) Applies settings tuned for curved overlay. | _not defined_ |
|
||||
| Setting | Description | Default |
|
||||
| -------------------------------- | ---------------------------------------------------------- | ------------------ |
|
||||
| `CIRQUE_PINNACLE_X_LOWER` | (Optional) The minimum reachable X value on the sensor. | `127` |
|
||||
| `CIRQUE_PINNACLE_X_UPPER` | (Optional) The maximum reachable X value on the sensor. | `1919` |
|
||||
| `CIRQUE_PINNACLE_Y_LOWER` | (Optional) The minimum reachable Y value on the sensor. | `63` |
|
||||
| `CIRQUE_PINNACLE_Y_UPPER` | (Optional) The maximum reachable Y value on the sensor. | `1471` |
|
||||
| `CIRQUE_PINNACLE_DIAMETER_MM` | (Optional) Diameter of the trackpad sensor in millimeters. | `40` |
|
||||
| `CIRQUE_PINNACLE_ATTENUATION` | (Optional) Sets the attenuation of the sensor data. | `ADC_ATTENUATE_4X` |
|
||||
| `CIRQUE_PINNACLE_CURVED_OVERLAY` | (Optional) Applies settings tuned for curved overlay. | _not defined_ |
|
||||
|
||||
**`CIRQUE_PINNACLE_ATTENUATION`** is a measure of how much data is suppressed in regards to sensitivity. The higher the attenuation, the less sensitive the touchpad will be.
|
||||
|
||||
|
@ -107,18 +107,18 @@ Default attenuation is set to 4X, although if you are using a thicker overlay (s
|
|||
* `ADC_ATTENUATE_2X`
|
||||
* `ADC_ATTENUATE_1X`: Most sensitive
|
||||
|
||||
| I2C Setting | Description | Default |
|
||||
|--------------------------|---------------------------------------------------------------------------------|---------|
|
||||
|`CIRQUE_PINNACLE_ADDR` | (Required) Sets the I2C Address for the Cirque Trackpad | `0x2A` |
|
||||
|`CIRQUE_PINNACLE_TIMEOUT` | (Optional) The timeout for i2c communication with the trackpad in milliseconds. | `20` |
|
||||
| I2C Setting | Description | Default |
|
||||
| ------------------------- | ------------------------------------------------------------------------------- | ------- |
|
||||
| `CIRQUE_PINNACLE_ADDR` | (Required) Sets the I2C Address for the Cirque Trackpad | `0x2A` |
|
||||
| `CIRQUE_PINNACLE_TIMEOUT` | (Optional) The timeout for i2c communication with the trackpad in milliseconds. | `20` |
|
||||
|
||||
| SPI Setting | Description | Default |
|
||||
|-------------------------------|------------------------------------------------------------------------|----------------|
|
||||
|`CIRQUE_PINNACLE_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `1000000` |
|
||||
|`CIRQUE_PINNACLE_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
|
||||
|`CIRQUE_PINNACLE_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `1` |
|
||||
|`CIRQUE_PINNACLE_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
|`CIRQUE_PINNACLE_SPI_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
| SPI Setting | Description | Default |
|
||||
| ------------------------------ | ---------------------------------------------------------------------- | ------------- |
|
||||
| `CIRQUE_PINNACLE_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `1000000` |
|
||||
| `CIRQUE_PINNACLE_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` |
|
||||
| `CIRQUE_PINNACLE_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `1` |
|
||||
| `CIRQUE_PINNACLE_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
| `CIRQUE_PINNACLE_SPI_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
|
||||
Default Scaling is 1024. Actual CPI depends on trackpad diameter.
|
||||
|
||||
|
@ -126,13 +126,13 @@ Also see the `POINTING_DEVICE_TASK_THROTTLE_MS`, which defaults to 10ms when usi
|
|||
|
||||
#### Cirque Trackpad gestures
|
||||
|
||||
| Gesture Setting | Description | Default |
|
||||
|-----------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------|
|
||||
|`POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE` | (Optional) Enable inertial cursor. Cursor continues moving after a flick gesture and slows down by kinetic friction | _not defined_ |
|
||||
|`CIRQUE_PINNACLE_CIRCULAR_SCROLL_ENABLE` | (Optional) Enable circular scroll. Touch originating in outer ring can trigger scroll by moving along the perimeter. Near side triggers vertical scroll and far side triggers horizontal scroll. | _not defined_ |
|
||||
|`CIRQUE_PINNACLE_TAP_ENABLE` | (Optional) Enable tap to click. This currently only works on the master side. | _not defined_ |
|
||||
|`CIRQUE_PINNACLE_TAPPING_TERM` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` |
|
||||
|`CIRQUE_PINNACLE_TOUCH_DEBOUNCE` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` |
|
||||
| Gesture Setting | Description | Default |
|
||||
| ---------------------------------------------- | ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ | -------------------- |
|
||||
| `POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE` | (Optional) Enable inertial cursor. Cursor continues moving after a flick gesture and slows down by kinetic friction | _not defined_ |
|
||||
| `CIRQUE_PINNACLE_CIRCULAR_SCROLL_ENABLE` | (Optional) Enable circular scroll. Touch originating in outer ring can trigger scroll by moving along the perimeter. Near side triggers vertical scroll and far side triggers horizontal scroll. | _not defined_ |
|
||||
| `CIRQUE_PINNACLE_TAP_ENABLE` | (Optional) Enable tap to click. This currently only works on the master side. | _not defined_ |
|
||||
| `CIRQUE_PINNACLE_TAPPING_TERM` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` |
|
||||
| `CIRQUE_PINNACLE_TOUCH_DEBOUNCE` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` |
|
||||
|
||||
**`POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE`** is not specific to Cirque trackpad; any pointing device with a lift/contact status can integrate this gesture into its driver. e.g. PMW3360 can use Lift_Stat from Motion register. Note that `POINTING_DEVICE_MOTION_PIN` cannot be used with this feature; continuous polling of `pointing_device_get_report()` is needed to generate glide reports.
|
||||
|
||||
|
@ -146,13 +146,13 @@ POINTING_DEVICE_DRIVER = pimoroni_trackball
|
|||
|
||||
The Pimoroni Trackball module is a I2C based breakout board with an RGB enable trackball.
|
||||
|
||||
| Setting | Description | Default |
|
||||
|-------------------------------------|------------------------------------------------------------------------------------|---------|
|
||||
|`PIMORONI_TRACKBALL_ADDRESS` | (Required) Sets the I2C Address for the Pimoroni Trackball. | `0x0A` |
|
||||
|`PIMORONI_TRACKBALL_TIMEOUT` | (Optional) The timeout for i2c communication with the trackball in milliseconds. | `100` |
|
||||
|`PIMORONI_TRACKBALL_SCALE` | (Optional) The multiplier used to generate reports from the sensor. | `5` |
|
||||
|`PIMORONI_TRACKBALL_DEBOUNCE_CYCLES` | (Optional) The number of scan cycles used for debouncing on the ball press. | `20` |
|
||||
|`PIMORONI_TRACKBALL_ERROR_COUNT` | (Optional) Specifies the number of read/write errors until the sensor is disabled. | `10` |
|
||||
| Setting | Description | Default |
|
||||
| ------------------------------------ | ---------------------------------------------------------------------------------- | ------- |
|
||||
| `PIMORONI_TRACKBALL_ADDRESS` | (Required) Sets the I2C Address for the Pimoroni Trackball. | `0x0A` |
|
||||
| `PIMORONI_TRACKBALL_TIMEOUT` | (Optional) The timeout for i2c communication with the trackball in milliseconds. | `100` |
|
||||
| `PIMORONI_TRACKBALL_SCALE` | (Optional) The multiplier used to generate reports from the sensor. | `5` |
|
||||
| `PIMORONI_TRACKBALL_DEBOUNCE_CYCLES` | (Optional) The number of scan cycles used for debouncing on the ball press. | `20` |
|
||||
| `PIMORONI_TRACKBALL_ERROR_COUNT` | (Optional) Specifies the number of read/write errors until the sensor is disabled. | `10` |
|
||||
|
||||
### PMW 3360 and PMW 3389 Sensor
|
||||
|
||||
|
@ -176,15 +176,15 @@ The CPI range is 50-16000, in increments of 50. Defaults to 2000 CPI.
|
|||
|
||||
Both PMW 3360 and PMW 3389 are SPI driven optical sensors, that use a built in IR LED for surface tracking.
|
||||
|
||||
| Setting | Description | Default |
|
||||
| ---------------------------- | ------------------------------------------------------------------------------------------- | ------------- |
|
||||
| `PMW33XX_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
| `PMW33XX_CS_PINS` | (Alternative) Sets the Cable Select pins connected to multiple sensors. | _not defined_ |
|
||||
| `PMW33XX_CPI` | (Optional) Sets counts per inch sensitivity of the sensor. | _varies_ |
|
||||
| `PMW33XX_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
|
||||
| `PMW33XX_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
| `PMW33XX_LIFTOFF_DISTANCE` | (Optional) Sets the lift off distance at run time | `0x02` |
|
||||
| `ROTATIONAL_TRANSFORM_ANGLE` | (Optional) Allows for the sensor data to be rotated +/- 127 degrees directly in the sensor. | `0` |
|
||||
| Setting | Description | Default |
|
||||
| ---------------------------- | ------------------------------------------------------------------------------------------ | ------------- |
|
||||
| `PMW33XX_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ |
|
||||
| `PMW33XX_CS_PINS` | (Alternative) Sets the Cable Select pins connected to multiple sensors. | _not defined_ |
|
||||
| `PMW33XX_CPI` | (Optional) Sets counts per inch sensitivity of the sensor. | _varies_ |
|
||||
| `PMW33XX_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `2000000` |
|
||||
| `PMW33XX_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ |
|
||||
| `PMW33XX_LIFTOFF_DISTANCE` | (Optional) Sets the lift off distance at run time | `0x02` |
|
||||
| `ROTATIONAL_TRANSFORM_ANGLE` | (Optional) Allows for the sensor data to be rotated +/- 30 degrees directly in the sensor. | `0` |
|
||||
|
||||
To use multiple sensors, instead of setting `PMW33XX_CS_PIN` you need to set `PMW33XX_CS_PINS` and also handle and merge the read from this sensor in user code.
|
||||
Note that different (per sensor) values of CPI, speed liftoff, rotational angle or flipping of X/Y is not currently supported.
|
||||
|
@ -237,15 +237,15 @@ void pointing_device_driver_set_cpi(uint16_t cpi) {}
|
|||
|
||||
## Common Configuration
|
||||
|
||||
| Setting | Description | Default |
|
||||
|----------------------------------|-----------------------------------------------------------------------|-------------------|
|
||||
|`POINTING_DEVICE_ROTATION_90` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_ROTATION_180` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_ROTATION_270` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_INVERT_X` | (Optional) Inverts the X axis report. | _not defined_ |
|
||||
|`POINTING_DEVICE_INVERT_Y` | (Optional) Inverts the Y axis report. | _not defined_ |
|
||||
|`POINTING_DEVICE_MOTION_PIN` | (Optional) If supported, will only read from sensor if pin is active. | _not defined_ |
|
||||
|`POINTING_DEVICE_TASK_THROTTLE_MS` | (Optional) Limits the frequency that the sensor is polled for motion. | _not defined_ |
|
||||
| Setting | Description | Default |
|
||||
| ---------------------------------- | --------------------------------------------------------------------- | ------------- |
|
||||
| `POINTING_DEVICE_ROTATION_90` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_ROTATION_180` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_ROTATION_270` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_INVERT_X` | (Optional) Inverts the X axis report. | _not defined_ |
|
||||
| `POINTING_DEVICE_INVERT_Y` | (Optional) Inverts the Y axis report. | _not defined_ |
|
||||
| `POINTING_DEVICE_MOTION_PIN` | (Optional) If supported, will only read from sensor if pin is active. | _not defined_ |
|
||||
| `POINTING_DEVICE_TASK_THROTTLE_MS` | (Optional) Limits the frequency that the sensor is polled for motion. | _not defined_ |
|
||||
|
||||
!> When using `SPLIT_POINTING_ENABLE` the `POINTING_DEVICE_MOTION_PIN` functionality is not supported and `POINTING_DEVICE_TASK_THROTTLE_MS` will default to `1`. Increasing this value will increase transport performance at the cost of possible mouse responsiveness.
|
||||
|
||||
|
@ -254,25 +254,25 @@ void pointing_device_driver_set_cpi(uint16_t cpi) {}
|
|||
|
||||
The following configuration options are only available when using `SPLIT_POINTING_ENABLE` see [data sync options](feature_split_keyboard.md?id=data-sync-options). The rotation and invert `*_RIGHT` options are only used with `POINTING_DEVICE_COMBINED`. If using `POINTING_DEVICE_LEFT` or `POINTING_DEVICE_RIGHT` use the common configuration above to configure your pointing device.
|
||||
|
||||
| Setting | Description | Default |
|
||||
|----------------------------------------|-----------------------------------------------------------------------|---------------|
|
||||
|`POINTING_DEVICE_LEFT` | Pointing device on the left side (Required - pick one only) | _not defined_ |
|
||||
|`POINTING_DEVICE_RIGHT` | Pointing device on the right side (Required - pick one only) | _not defined_ |
|
||||
|`POINTING_DEVICE_COMBINED` | Pointing device on both sides (Required - pick one only) | _not defined_ |
|
||||
|`POINTING_DEVICE_ROTATION_90_RIGHT` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_ROTATION_180_RIGHT` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_ROTATION_270_RIGHT` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
|
||||
|`POINTING_DEVICE_INVERT_X_RIGHT` | (Optional) Inverts the X axis report. | _not defined_ |
|
||||
|`POINTING_DEVICE_INVERT_Y_RIGHT` | (Optional) Inverts the Y axis report. | _not defined_ |
|
||||
|`MOUSE_EXTENDED_REPORT` | (Optional) Enables support for extended mouse reports. (-32767 to 32767, instead of just -127 to 127) |
|
||||
| Setting | Description | Default |
|
||||
| ------------------------------------ | ----------------------------------------------------------------------------------------------------- | ------------- |
|
||||
| `POINTING_DEVICE_LEFT` | Pointing device on the left side (Required - pick one only) | _not defined_ |
|
||||
| `POINTING_DEVICE_RIGHT` | Pointing device on the right side (Required - pick one only) | _not defined_ |
|
||||
| `POINTING_DEVICE_COMBINED` | Pointing device on both sides (Required - pick one only) | _not defined_ |
|
||||
| `POINTING_DEVICE_ROTATION_90_RIGHT` | (Optional) Rotates the X and Y data by 90 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_ROTATION_180_RIGHT` | (Optional) Rotates the X and Y data by 180 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_ROTATION_270_RIGHT` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ |
|
||||
| `POINTING_DEVICE_INVERT_X_RIGHT` | (Optional) Inverts the X axis report. | _not defined_ |
|
||||
| `POINTING_DEVICE_INVERT_Y_RIGHT` | (Optional) Inverts the Y axis report. | _not defined_ |
|
||||
| `MOUSE_EXTENDED_REPORT` | (Optional) Enables support for extended mouse reports. (-32767 to 32767, instead of just -127 to 127) |
|
||||
|
||||
!> If there is a `_RIGHT` configuration option or callback, the [common configuration](feature_pointing_device.md?id=common-configuration) option will work for the left. For correct left/right detection you should setup a [handedness option](feature_split_keyboard?id=setting-handedness), `EE_HANDS` is usually a good option for an existing board that doesn't do handedness by hardware.
|
||||
|
||||
|
||||
## Callbacks and Functions
|
||||
|
||||
| Function | Description |
|
||||
|-----------------------------------|----------------------------------------------------------------------------------------------------------------------------------------|
|
||||
| Function | Description |
|
||||
| ---------------------------------------------------------- | ------------------------------------------------------------------------------------------------------------- |
|
||||
| `pointing_device_init_kb(void)` | Callback to allow for keyboard level initialization. Useful for additional hardware sensors. |
|
||||
| `pointing_device_init_user(void)` | Callback to allow for user level initialization. Useful for additional hardware sensors. |
|
||||
| `pointing_device_task_kb(mouse_report)` | Callback that sends sensor data, so keyboard code can intercept and modify the data. Returns a mouse report. |
|
||||
|
@ -280,11 +280,11 @@ The following configuration options are only available when using `SPLIT_POINTIN
|
|||
| `pointing_device_handle_buttons(buttons, pressed, button)` | Callback to handle hardware button presses. Returns a `uint8_t`. |
|
||||
| `pointing_device_get_cpi(void)` | Gets the current CPI/DPI setting from the sensor, if supported. |
|
||||
| `pointing_device_set_cpi(uint16_t)` | Sets the CPI/DPI, if supported. |
|
||||
| `pointing_device_get_report(void)` | Returns the current mouse report (as a `mouse_report_t` data structure). |
|
||||
| `pointing_device_set_report(mouse_report)` | Sets the mouse report to the assigned `mouse_report_t` data structured passed to the function. |
|
||||
| `pointing_device_send(void)` | Sends the current mouse report to the host system. Function can be replaced. |
|
||||
| `pointing_device_get_report(void)` | Returns the current mouse report (as a `mouse_report_t` data structure). |
|
||||
| `pointing_device_set_report(mouse_report)` | Sets the mouse report to the assigned `mouse_report_t` data structured passed to the function. |
|
||||
| `pointing_device_send(void)` | Sends the current mouse report to the host system. Function can be replaced. |
|
||||
| `has_mouse_report_changed(new_report, old_report)` | Compares the old and new `mouse_report_t` data and returns true only if it has changed. |
|
||||
| `pointing_device_adjust_by_defines(mouse_report)` | Applies rotations and invert configurations to a raw mouse report. |
|
||||
| `pointing_device_adjust_by_defines(mouse_report)` | Applies rotations and invert configurations to a raw mouse report. |
|
||||
|
||||
|
||||
## Split Keyboard Callbacks and Functions
|
||||
|
@ -292,7 +292,7 @@ The following configuration options are only available when using `SPLIT_POINTIN
|
|||
The combined functions below are only available when using `SPLIT_POINTING_ENABLE` and `POINTING_DEVICE_COMBINED`. The 2 callbacks `pointing_device_task_combined_*` replace the single sided equivalents above. See the [combined pointing devices example](feature_pointing_device.md?id=combined-pointing-devices)
|
||||
|
||||
| Function | Description |
|
||||
|-----------------------------------------------------------------|--------------------------------------------------------------------------------------------------------------------------|
|
||||
| --------------------------------------------------------------- | ------------------------------------------------------------------------------------------------------------------------ |
|
||||
| `pointing_device_set_shared_report(mouse_report)` | Sets the shared mouse report to the assigned `mouse_report_t` data structured passed to the function. |
|
||||
| `pointing_device_set_cpi_on_side(bool, uint16_t)` | Sets the CPI/DPI of one side, if supported. Passing `true` will set the left and `false` the right` |
|
||||
| `pointing_device_combine_reports(left_report, right_report)` | Returns a combined mouse_report of left_report and right_report (as a `mouse_report_t` data structure) |
|
||||
|
|
|
@ -1,3 +1,4 @@
|
|||
// Copyright 2022 Daniel Kao (dkao)
|
||||
// Copyright 2022 Stefan Kerkmann (KarlK90)
|
||||
// Copyright 2022 Ulrich Spörlein (@uqs)
|
||||
// Copyright 2021 Alabastard (@Alabastard-64)
|
||||
|
@ -165,7 +166,7 @@ bool pmw33xx_init(uint8_t sensor) {
|
|||
wait_ms(1);
|
||||
|
||||
pmw33xx_write(sensor, REG_Config2, 0x00);
|
||||
pmw33xx_write(sensor, REG_Angle_Tune, CONSTRAIN(ROTATIONAL_TRANSFORM_ANGLE, -127, 127));
|
||||
pmw33xx_write(sensor, REG_Angle_Tune, CONSTRAIN(ROTATIONAL_TRANSFORM_ANGLE, -30, 30));
|
||||
pmw33xx_write(sensor, REG_Lift_Config, PMW33XX_LIFTOFF_DISTANCE);
|
||||
|
||||
if (!pmw33xx_check_signature(sensor)) {
|
||||
|
|
|
@ -1,3 +1,4 @@
|
|||
// Copyright 2022 Daniel Kao (dkao)
|
||||
// Copyright 2022 Stefan Kerkmann (KarlK90)
|
||||
// Copyright 2022 Ulrich Spörlein (@uqs)
|
||||
// Copyright 2021 Alabastard (@Alabastard-64)
|
||||
|
@ -58,6 +59,10 @@ _Static_assert(sizeof((pmw33xx_report_t){0}.motion) == 1, "pmw33xx_report_t.moti
|
|||
# define ROTATIONAL_TRANSFORM_ANGLE 0x00
|
||||
#endif
|
||||
|
||||
#if ROTATIONAL_TRANSFORM_ANGLE > 30 || ROTATIONAL_TRANSFORM_ANGLE < (-30)
|
||||
# error ROTATIONAL_TRANSFORM_ANGLE has to be in the range of +/- 30 for all PMW33XX sensors.
|
||||
#endif
|
||||
|
||||
// Support single and plural spellings
|
||||
#ifndef PMW33XX_CS_PINS
|
||||
# ifndef PMW33XX_CS_PIN
|
||||
|
|
Loading…
Reference in a new issue