* Add suspend functions
* Disable RGB code if it's disabled
* Add keyboard_init functions
* Change where references so it will compile
* Wrong command chained in wake up kb function
* Fix non-feature file changes
* Add documentation
* Re-add matrix init docs
* add rgblight code to example
* Remove suspend code
* Clean up docs
* Fix docs
* Fix suspend code
* more doc fixes
* change function to startup_* rather than keyboard_init_
* fix spelling error
* fix up docs to finish removing keyboard_init
* Use Pre and Post init functions
* Update Documenation
* Remove changes to my keymap and userspace code
* Cleanup
* Revert changes to extra files
* Forgot a semicolon
* Make sure all protocols call keyboard_setup
* Cleanup functions
* Unset startup_user
* Remove changes from division keyboard
* Readd startup_user function
* Remove all to startup_user
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Update docs/custom_quantum_functions.md
Co-Authored-By: drashna <drashna@live.com>
* Add suggestion line
* Rebase fixes
* Update documentation to be more useful/accurate
* Cleanup of documentation
* Fix spacing inconsistency
* Revert unexpected change to keymap
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
* Add ability to animate arm_atsam led matrix from the center of a circle
* Make arm_atsam led matrix circular animation circular rather than obloid
* Fix indentation in tmk_core led_matrix.c
When this if statement is false, it will cause the report ID to be read as the LED state.
We already know there are two bytes in the endpoint, which is a reasonably good indicator that it contains a report ID, so we should always read both.
* Check the size of the SET_REPORT packet
If we have two bytes, that probably means the first is a report ID. The 6KRO interface may or may not have one, but the NKRO interface always does, so we need to check this regardless of whether KEYBOARD_SHARED_EP is defined.
* Fix indentation
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
* initial commit, this now mostly works
- RGB controls work
- Dynamic keymap still broken due to eeprom
- Via works
* STM32 eeprom update
- Update EEPROM emulation library to handle 8bit data like AVR.
- This library also allows for multiple page pairs resulting in greater EEPROM size flexibility
* hs60 changes
* HS60 hhkb added
* Update keyboards/hs60/v2/config.h
Co-Authored-By: yiancar <yiangosyiangou@cytanet.com.cy>
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
* Add initial support for vertically-oriented animations
* DRY up vertical animation support
* Fix animation code for arm_atsam led_matrix to work in all directions
* Adjust py calculation to base off bottom rather than top
* Unify multiple HID interfaces into one
This reduces the number of USB endpoints required, which frees them up
for other things.
NKRO and EXTRAKEY always use the shared endpoint.
By default, MOUSEKEY also uses it. This means it won't work as a Boot
Procotol mouse in some BIOSes, etc. If you really think your
keyboard needs to work as a mouse in your BIOS, set
MOUSE_SHARED_EP = no in your rules.mk.
By default, the core keyboard does not use the shared endpoint, as not
all BIOSes are standards compliant and that's one place you don't want
to find out your keyboard doesn't work.. If you are really confident,
you can set KEYBOARD_SHARED_EP = yes to use the shared endpoint here
too.
* unify endpoints: ChibiOS protocol implementation
* fixup: missing #ifdef EXTRAKEY_ENABLEs
broke build on AVR with EXTRAKEY disabled
* endpoints: restore error when too many endpoints required
* lufa: wait up to 10ms to send keyboard input
This avoids packets being dropped when two reports are sent in quick
succession (eg. releasing a dual role key).
* endpoints: fix compile on ARM_ATSAM
* endpoint: ARM_ATSAM fixes
No longer use wrong or unexpected endpoint IDs
* endpoints: accommodate VUSB protocol
V-USB has its own, understandably simple ideas about the report formats.
It already blasts the mouse and extrakeys through one endpoint with
report IDs. We just stay out of its way.
* endpoints: document new endpoint configuration options
* endpoints: respect keyboard_report->mods in NKRO
The caller(s) of host_keyboard_send expect to be able to just drop
modifiers in the mods field and not worry about whether NKRO is in use.
This is a good thing. So we just shift it over if needs be.
* endpoints: report.c: update for new keyboard_report format
Rewrote USB state tracking for implementation of suspend state.
Updated suspend.c in entirety.
Main subtasks (generally hardware related) are now run prior to keyboard task.
* add computed pins from mcu type
* update for atmega32a
* doc typo
* add atmega16 chips, link to references
* remove avr include from config
* exclude assembler in config.h includes
* consolodate options, add 646
* fix typo in pindef
* Converter: add XT USB converter from TMK
* Converter: port TMK code for USB converter to QMK
* Apply requested changes after code review by @drashna
- use "pragma once" instead of include guards
- use LAYOUT instead of KEYMAP
- allow customisation with matrix_init_user() and matrix_scan_user()
- set BOOTLOADER instead of BOOTLOADER_SIZE
- Add XT_ENABLE to OPT_DEFS
* Remove unnecessary lines
Added hid_listen USB device for arm_atsam USB protocol.
Debug printing is now done through the console device (CONSOLE_ENABLE = yes) rather than the virtser device, for viewing in hid_listen.
Function dpf(...) renamed to CDC_printf(...) and should now be called directly if intending to print to the virtual serial device.
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* add temporary test code rgblight-macro-test1.[ch]
* rgblight.h : mode auto numberring and auto generate mode name symbol
No change in build result.
* rgblight.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* quantum.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* fix build break. when RGB_MATRIX_ENABLE defined
* add temporary test code rgblight-macro-test2.[ch]
* modify rgblight_mode_eeprom_helper() and rgblight_sethsv_eeprom_helper()
* modify rgblight_task()
* configurable each effect compile on/off in config.h
* update docs/feature_rgblight.md
* fix conflict. docs/feature_rgblight.md
* remove temporary test code rgblight-macro-test*.[ch]
* fix comment typo.
* remove old mode number from comment
* update docs/feature_rgblight.md about effect mode
* Revert "update docs/feature_rgblight.md about effect mode"
This reverts commit 43890663fcc9dda1899df7a37d382fc38b1a6d6d.
* some change docs/feature_rgblight.md
* fix typo
* docs/feature_rgblight.md update: revise mode number table
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
- Added support for NO_USB_STARTUP_CHECK. This allows the keyboard do function and not get stuck in a SUSPENDED state loop in case of no USB connection.
- Added support for WAIT_FOR_USB. In LUFA no keyboard has this flag enable therefor no keyboard waits for usb to be active.
- Added documentation for both configuration flags as they were missing.
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
* STM32 EEPROM Emulation
- Added EEPROM emulation libaries from libmaple and Arduino_STM32. https://github.com/rogerclarkmelbourne/Arduino_STM32 and https://github.com/leaflabs/libmaple.
- Renamed teensy EEPROM library and added conditional selection of library.
- Remapped EEPROM memory map for 16 byte blocks (as is with STM32f3xx MCUs).
- Added EEPROM initialization in main.c of Chibios.
- Added EEPROM format to clear the emulated pages when EEPROM is marked as invalid.
* Fixed ifdef
* Massdrop SAMD51
Massdrop SAMD51 keyboards initial project upload
* Removing relocated files
Removing files that were relocated and not deleted from previous location
* LED queue fix and cleaning
Cleaned some white space or comments.
Fix for LED I2C command queue.
Cleaned up interrupts.
Added debug function for printing numbers to scope through m15 line.
* Factory programmed serial usage
Ability to use factory programmed serial in hub and keyboard usb descriptors
* USB serial number and bugfix
Added support for factory programmed serial and usage.
Incorporated bootloader's conditional compiling to align project closer.
Fixed issue when USB device attempted to send before enabled.
General white space and comment cleanup.
* Project cleanup
Cleaned up project in terms of white space, commented code, and unecessary files.
NKRO keyboard is now using correct setreport although KBD was fine to use.
Fixed broken linkage to __xprintf for serial debug statements.
* Fix for extra keys
Fixed possible USB hang on extra keys report set missing
* I2C cleanup
I2C cleanup and file renames necessary for master branch merge
* Boot tracing and clocks cleanup
Added optional boot debug trace mode through debug LED codes.
General clock code cleanup.
* Relocate ARM/Atmel headers
Moved ARM/Atmel header folder from drivers to lib and made necessary makefile changes.
* Pull request changes
Pull request changes
* Keymap and compile flag fix
Keymap fix for momentary layer.
Potential compile flag fix for Travis CI failure.
* va_list include fix
Fix for va_list compile failure
* Include file case fixes
Fixes for include files with incorrect case
* ctrl and alt67 keyboard readme
Added ctrl and alt67 keyboard readme files
* initial files for rev 6 with encoder
* music map init, dip scan added
* adds ws2812 driver for arm
* flesh out dip and encoder support
* adds default encoder res
* adds default encoder res
* start muse implementation
* muse working with encoder as control
* flip direction
* try mouse wheel again
* dont break other revs
* dont break other revs
* conditional autio
* pwm ws driver (not working)
* update build includes for chibios
* update ws2812 driver/config
* last commit for glasser code
* working example
* remove rgb for now
* finish up rev6
* working encoder keycodes
* add warnings to planck keymaps about the LAYOUT
* Copy Chibios serial_usb_driver into the chibios/protocol
It's renamed to usb_driver to avoid name conflicts
* Make the usb driver compile
* Disable ChibiOS serial usb driver for all keyboards
* Change usb_main to use QMKUSBDriver
* Initialize the usb driver buffers
* Add support for fixed size queues
* Fix USB driver initialization
* Don't transfer an empty packet for fixed size streams
* Generate api docs from source code
* Add a bunch of doxygen comments
* more doxygen comments
* Add the in-progress api docs
* script to generate docs from travis
* Add doc generation to the travis job
* make travis_docs.sh commit the work it does
* make sure the docs script exits cleanly
* Move lufa descriptor to protocol/usb_descriptor
* Try to compile usb_descriptor on ChibiOS
* Add lufa_utils for ChibiOS
Lufa USB descriptors for ChibiOS
* More lufa_util compatibility fixes
* First compiling version of shared USB descriptor
* Send the usb descriptors
* Fix the CONSOLE output on ChibiOS
* Add errors for unsupported interfaces
* Enable support for vitual serial port USB descriptors
* Implement virtual serial port for ChibiOS
* Cleanup the lufa_utils
Use the default lufa header files
* Add raw hid support for ChibiOS
This is completely untested
* Enable midi compilation on ChibiOS
* Move midi functionality out of lufa.c
* Don't register sysex callback when not needed
* ChibiOS compilation fixes
* Update ChibiOS submodule
* Fix the Midi USB descriptor
It didn't work properly when both Midi and Virtual serial port was enabled.
* Add MIDI support for ChibiOS
* Fix USB descriptor strings on ChibiOS
* Use serial usb driver for raw hid
* Generalize the ChibiOS stream like drivers
This makes the initialization much more simple and eliminates a lot of
the code duplication.
* Convert console output to chibios stream driver
* Fixes for ChibiOS update
* Update the ChibiOS contrib submodule
To include the usb data toggle synchronization fixes
* Fix duplicate reset enumeration on ChibiOS
* Add missing include
* Add number of endpoints check for ChibiOS
* Enable serial USB driver on all keyboards
* Add missing includes when API is enabled withot midi
* Add another missing inlcude
* Add NIU Mini keymap from Planck keymap
* Remove old keymap files
* Fix README, removed Planck references
* Add default layout, move Planck layout to separate folder
* Update README
* Add my XD60 keymap
* Change RShift to slash
* Fix keymap: stuck on MO(1)
* Move RESET to Fn+Enter
* Add: RGB saturation cycle
* Add numpad layer to keymap
* Fix last case
* Cleanup Mechmini keymap. Once the custom RGB function is defined, there is no need to manually handle RGB code.
* Change default to KEYMAP_MIT, not KEYMAP_OFFSET
* Add custom RGB code for JJ40
* Reset Mechmini advertised power draw to 500. Will have to test actual maximum power draw later.
* RGB working on JJ40.
* Fix: saturation increase/decrease flipped
* Add new directory for my custom keymap with RGB keycodes
* Swap LAlt and LGUI
* Update JJ40 max power draw with measured value
* Update: fun40 rules.mk to enable underglow; earlier failed Travis CI
* Fix: init RGB LEDs on boot. Also added HHKB-like keymap for XD60.
* Super rudimentary backlight test, init RGB LEDs on boot
* Backlighting works - stays on for now
* Toggling working
* Now can override backlight.c functions. Problem was functions in backlight.c weren't called before due to a lack of matrix_scan_quantum() in matrix.c
* Timers not working
* Delete global.h
* Cleanup
* Compiles
* Good sign: LEDs stop working again
* Handle timer1 overflow
* Progress: fix: forgot to init
* Backlighting fully working now except breathing.
* Revert keymap to original keycodes
* Update XD60 keymap README
* Update JJ40 keymap with backlight toggles
* Breathing working just fine.
* Update references
* Add backlight_set() call
* Cleanup code to disable backlight
* Fix: does not compile
* Fix: missing call to rgblight_task.
* Testing with BACKLIGHT_BREATHING
* Cleanup
* Cleanup comments
* More commenting cleanup.
* Do not enable BACKLIGHT_BREATHING by default
* Update XD60 keymap
* Update: move matrix_scan_kb out from matrix.c to jj40.c (kb-level)
* Cleanup for PR
* Fix conflict in readme.md for NIU mini
* Restore original power consumption figure
* Fix: matrix_scan_user() now has to be defined in the keymaps
* Add weak `matrix_scan_user` so it does not have to be defined in keymap
* Add weak matrix_init_user()
