* Add support for hardware and board initialisation overrides.
* qmk cformat.
* Add some documentation.
* Docs clarity.
* Make early_hardware_init_pre a no-op for now, until migrations occur.
* Doco update
* Make distinction between keyboard and ChibiOS board in docs
* Doc anchors.
* Update tmk_core/protocol/chibios/main.c
Co-Authored-By: Joel Challis <git@zvecr.com>
* Rework bootloader entry to be off by default, allow opting-in.
Co-authored-by: Joel Challis <git@zvecr.com>
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Add Word Per Minute calculation feature
* Fix copyright info
* Remove header from quantum.c, setup overloadable keycode inclusion for WPM, update docs
* Simplify logic for keycode filtering
* Adding link from summary to wpm_feature info
* Update docs/feature_wpm.md
Typo in function prototype example in docs
Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>
* Add WPM transport via i2c
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* [Docs] Update layer documentation
* Add layer_state_cmp functions
* Fix cut/copy/paste issue
* Add id tags
* Apply noroads corrections
* Move Layers section to separate document
* Fix ID tag for layers
* Use better name for summary/side bar
* Fix feature page linkage
As well as a small spell error close by
* Remove paper analogy for now
* fix some broken links
* remove duplicate and confusing material from cli.md
* Switch brazil to the 2 letter country code
* Update docs/_langs.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
* Improve support and docs for ADC driver
* Comment ADC channels
* Move to Makers and Modders section, and fix usage instructions
* Flesh out intro
* Superscript 328P note
* Fix pin_to_mux LUT
* Support USB64/1287 as well
* analogReadPin() defaults to 0V mux on invalid pin
* Update pinToMux() function documentation
* Dot
* Accept (some of) the `qmk cformat` changes
* Do clang-format properly
* More wording tweaks
* Link to encoder docs
* Add "Resynchronizing an Out-of-Sync Git Branch" doc
* Update (Git) Best Practices doc title and filename
* Rename Branch Resync doc
* fork Best Practices doc into multiple files
* Add the doc list to Git Best Practices doc
* Update sidebar
* Update internal references
* Update sidebar - add subsection
* Update Your Fork's Master page title
* title case on Git Best Practices main doc
* ... and in the Resynchronizing a Branch doc
* Please read Part 1
I worked really hard on this, okay?
* Please use branches, too.
* suggestions by mtei
* change note about adding multiple files
* note that the name given the remote repo is arbitrary
* suggestions by fauxpark
* Git Best Practices -> Best Git Practices
Reads more naturally.
* rephrase hint block regarding remote name
* rework the resynchronization instructions per mtei
* use hint boxes for reference to Part 1 doc
I may be addicted to hint boxes. I'm sorry fauxpark. 😢
* add some clarity about the upstream repo
* wordsmithing per mtei
* restyle the shell code blocks
Makes them more consistent to the other docs in this section.
* Set up language fallback for docs, and update translation guidelines
* Title Case
* Add ID example
* Link to emoji flag cheatsheet
* Move docs preview section to contributing.md
* Point to docs preview in the readme
* Tidy up compatible MCUs docs
* ARM chips should have USB
* 32KB soft lower limit applies to ARM as well
* NXP is the manufacturer name, not Kinetis
* Units
* Rework how bin/qmk handles subcommands
* qmk config wip
* Code to show all configs
* Fully working `qmk config` command
* Mark some CLI arguments so they don't pollute the config file
* Fleshed out config support, nicer subcommand support
* sync with installable cli
* pyformat
* Add a test for subcommand_modules
* Documentation for the `qmk config` command
* split config_token on space so qmk config is more predictable
* Rework how subcommands are imported
* Document `arg_only`
* Document deleting from CLI
* Document how multiple operations work
* Add cli config to the doc index
* Add tests for the cli commands
* Make running the tests more reliable
* Be more selective about building all default keymaps
* Update new-keymap to fit the new subcommand style
* Add documentation about writing CLI scripts
* Document new-keyboard
* Update docs/cli_configuration.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/cli_development.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/cli_development.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Update docs/cli_development.md
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Address yan's comments.
* Apply suggestions from code review
suggestions from @noahfrederick
Co-Authored-By: Noah Frederick <code@noahfrederick.com>
* Apply suggestions from code review
Co-Authored-By: Noah Frederick <code@noahfrederick.com>
* Remove pip3 from the test runner
* Add Dip Switches as a core feature
* Add documentation for Dip Switch feature
* Update Preonic Rev3 to use new feature and remove custom matrix
* Apply suggestions from code review
Co-Authored-By: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
* Remove custom matrix line completely
Rather than just disabling it
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* DIP changes
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Use better check for DIP Switch configuration
* Add to show features
* Add bitmask callback for dip switch
* Fix OLKB Boards dip switch config
* Update docs to include bitmask example
* Fix comments/documentation
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Fix issues with docs and use example from @tuzonghua
* Fix wording
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Fix example to use proper formatting
Bad, BAAAAAAD drashna!!!
* Handle dip switch initialization better
* Add Zadig 101 to docs
* Add USBasp bootloader name
* Add links to the page
* Note the usual VIDs and PIDs for the bootloaders
* Add "List All Devices" note, just in case
* Talk about keyboard-specific bootloader procedures
* Send users to the new page in "Unknown Device for DFU Bootloader" section
* Halfkay bootloaders are also an exception here
* Script to generate keymap.c from JSON file.
* Support for keymap.json
* Add a warning about the keymap.c getting overwritten.
* Fix keymap generating
* Install the python deps
* Flesh out more of the python environment
* Remove defunct json2keymap
* Style everything with yapf
* Polish up python support
* Hide json keymap.c into the .build dir
* Polish up qmk-compile-json
* Make milc work with positional arguments
* Fix a couple small things
* Fix some errors and make the CLI more understandable
* Make the qmk wrapper more robust
* Add basic QMK Doctor
* Clean up docstrings and flesh them out as needed
* remove unused compile_firmware() function
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Experimental LED support (untested)
* Draft commit of typing speed RGB control
* More information in the readme
* Support all RGB animation modes (Fixes#1)
* Added support for all RGB light modes to use typing speed
Except christmas lights because that is seizure-inducing at high speeds!
* Introduced a value range specific to each RGB mode
Because some modes are a little too much when running at full speed!
* Update readme.md
* Update readme.md
* Re-arrange typing_speed definitions (Fixes#5) (#6)
* Re-arrange variable definitions to avoid including quantum.h from rgblight.c
* Fix a compilation error when trying to run make test:all
* Tweaks to the typing speed decay rate
* Renamed to momentum; moved implementation into dedicated files
* Groundwork for toggling momentum on/off (currently always on)
* Add EEPROM toggle for momentum-matching
* Moved momentum out of RGBLIGHT_ENABLE toggles so it's more generic
* Move momentum decay task out of rgblight_task()
* Fix missing momentum.h in lufa.c
* Added documentation
* Renamed feature to velocikey
* Reverted readme to original state
* Correct the readme title
* Updated feature name in the docs
* Update EECONFIG name
* Add compile-time toggles for velocikey
* Update feature documentation
* Revert "Merge branch 'led-support' into master"
This reverts commit e123ff5febf61639b9a9020748e1c2e2313460ff, reversing
changes made to df111a55b9d4929182e16108b1c0ead15b16df97.
* Move velocikey EECONFIG definition to depend on VELOCIKEY_ENABLE
* Rename decay_task function to decelerate
* Apply suggestions from code review
Co-Authored-By: chrislewisdev <chris@chrislewisdev.com>
* Re-order eeconfig definitions
* Apply coding conventions
* Apply #ifdef check in lufa.c
* Refactored interval time checks into one functionc
* Small rename
* Fix unused function error for layouts not using all rgb effects
* Only update EEPROM if Velocikey is enabled
* Incorporate code review feedback
* Small adjustment to top-end decay rate
* Add Velocikey documentation to table of contents
* Bring tetris:default keymap size down by disabling audio
* adds proton c base
* fixes custom matrix include
* adds readme.md
* initial proton coversion, no pin mapping
* start of mcu selection
* add pin mapping and sweet16 test
* add at90 to list
* disable backlight, fix d7
* update flag names
* doc updates
* proton c update for mcu selection
Specifically, moved the shifted keycodes to the top of the 'Feature' list, so it's more visible. This way, all of the keycodes are at the top of the list, rather than having the shifted keys at the bottom, so they should be easier to find since they're all in one place.
