* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Update tmk_core/common/progmem.h
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update quantum/rgblight.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fixed problem with implicit declaration in quantum/rgblight.c (#8381)
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update switch to array to allow custom values
* Add adc keymap
* update docs to reflect alignment of default 10 bit
* start conversion to USE_ADCVn
* samplerate is hella wrong...stub out for now
* basic f1 and f4 functionality
* Tidy up current changes
* Restore old pinToMux function
* Add back sample rate for supported platforms
* F0 compile fixes
* wordsmithery
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Remove reference to avr only function
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for STM32L0/L1 onboard EEPROM.
* Update docs/eeprom_driver.md
Co-Authored-By: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Add buffer based single line pan, arbitrary byte write to buffer
* Change dirty mask to inverse of OLED_BLOCK_TYPE for future proofing larger buffer sizes
* Updating docs to include new functions
* Updating to clarify scroll vs pan
* Fix out of bound OLED font access
The default font is 1344 bytes, or a total of 224 glyphs (each 6-bytes wide).
OLED_FONT_END defaults to 224, which if used will then index off the end of
the font array. So either the documentation or code is wrong.
Instead of figuring out the rewording of the documentation, just change
the OLED_FONT_END default value to 223, to match the documentation and code.
* Add static assert to check array size
Build bomb if the font array size doesn't match to the defines.
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
* Run clang-format manually to fix recently changed files
* Run clang-format manually to fix recently changed files - revert template files
* Run clang-format manually to fix recently changed files - format off for ascii_to_keycode_lut
* Add i2c_transmit_receive function
This function is listed in the ARM header file, but doesn't actually exist.
* Remove i2c_transmit_receive function
* Update DRV2605L read function to use i2c_readReg on both arm and avr
* Add central location for chibios defines
* Add central location for chibios defines - actually add files this time....
* Add Copyright header
* Update include order to resolve i2cv1 build errors
* Improve support and docs for ADC driver
* Comment ADC channels
* Move to Makers and Modders section, and fix usage instructions
* Flesh out intro
* Superscript 328P note
* Fix pin_to_mux LUT
* Support USB64/1287 as well
* analogReadPin() defaults to 0V mux on invalid pin
* Update pinToMux() function documentation
* Dot
* Accept (some of) the `qmk cformat` changes
* Do clang-format properly
* More wording tweaks
* Link to encoder docs
* IS31FL3733 Dirty page fix
Function IS31FL3733_update_led_control_registers was never setting update register to false. As a result the led on/off page was being written every transaction even when it was not modified. This is ineficient and causes lots of bandwidth use.
-> Fix the IS31FL3733_update_led_control_registers.
-> After testing it was evident that failed I2C transactions could corrupt the Led on/off register.
-> Update IS31FL3733_write_pwm_buffer and IS31FL3733_write_register functions to return 0 upon succesful tranmission and 1 if any of the transmitions within the function fail.
-> Modify IS31FL3733_update_pwm_buffers function so if any of the IS31FL3733_write_pwm_buffer transuction fails, the g_led_control_registers_update_required register is set to true forcing a rewrite of the led on/off register in case it was corrupted.
* Minor comment update
* Upsie:)
* Update is31fl3733.c
* Return fix
* more return fix
* type change
* more boolian logic reversal:)
* Error out when Solenid pin is not defined
Instead of defaulting to a (literally) random pin, error out instead. Because this pin may be used, or because that pin may not be exposed, or may not exist.
* Remove 'SOLENOID_ACTIVE' setting since it's not used
* Update documentation
* Move Ergodox EZ RGB code to custom driver
Also implements full addressing of Ergodox EZ's LED Strip, as written by seebs
Co-authored-by: Seebs <seebs@seebs.net>
* Make Clipping range accessible for custom drivers
* Remove RGBW_BB_TWI from driver and docs
* Revert changes to clipping range support
* Use just rgblight_set instead of full custom driver
* Convert to i2c_master commands
* Rename rgblight driver and clean up includes
